Can i remove onstar

Screw the screws in, not forgetting the cargo net if there was one in the car. Put the tire back onto the plate, tighten the nut clockwise if it needs to be and then put the liner over the tire.

Make sure it is secure in place and then close the trunk. If all wires were unplugged, the Onstar will be successfully turned off. Its primary Your email address will not be published. Let us know what you have to say:. Save my name, email, and website in this browser for the next time I comment.

Define your site main menu. How to Disable Onstar. Set the liner to the side. Remove the spare tire. There may be a wingnut holding the spare tire in place. If so, turn the wingnut counter-clockwise to unscrew it and loosen the tire.

Remove the cargo net, if you have one. Unscrew the net. If this net exist, these are the only screws you will have to remove to unscrew the tire plate. If you don't have a cargo net, see step 5. Remove the trunk still plate. Step 5: Pull the right side panel down and toward the front of the car.

Facing the right side of the trunk compartment, begin pulling the panel off at the top right-hand corner and down in a diagonal fashion toward the bottom left-hand corner. This will reveal the OnStar box. Step 6: Remove the three connectors on the OnStar module box. Press the tab down on the cord end that connects with the module box port and pull the connector right out. These connectors are similar to landline telephone cord connectors and should be easy to remove. Step 7: Repeat for remaining connectors.

Repeat with the other two connectors until all three have been removed from the OnStar module. Step 8: Replace all components. Use the reverse order of the above steps to replace the pieces in their original positions, except, of course, for the OnStar connectors. The benefits of OnStar can be outweighed by its cost or intrusiveness. For most people, simply cancelling the OnStar subscription is enough. This does not prevent OnStar from being able to retrieve data from your vehicle, however.

The most popular service booked by readers of this article is Trunk does not lock or open Inspection. Our certified mobile mechanics perform over services, including diagnostics, brakes, oil changes, scheduled mileage maintenances, and will come to you with all necessary parts and tools.

Our certified mobile mechanics make house calls in over 2, U. Fast, free online quotes for your car repair. Trunk does not lock or open Inspection Cost. Service Location. Method 1 of 2: Cancel your subscription Step 1: Visit the Onstar website. Tip : If you have any trouble, call OnStar directly to speak to a representative at 1. Note : Often, there is a wing bolt holding the spare tire in place, which can be rotated counterclockwise with your fingers, allowing you to lift the tire up and out.

Note : It is not necessary to completely remove this panel. As soon as you can see and access the OnStar module box, you can stop pulling the panel out of place. You should be able to slide the silver metal OnStar module its mount without having to unscrew anything.

Skip down to step 7 once you see the silver box in the panel. Remove the trunk's liner. The liner isn't secured by any screws or nuts, so you should be able to easily lift it out from the trunk. Just grab it from one edge and lift it upward. After removing the liner, set it aside and look at the newly revealed space. Lift out the spare tire. If your vehicle has a spare tire in it, you will need to remove it from the trunk and set it aside for now.

Use a screwdriver and twist the nut counterclockwise to remove it. After removing the nut, lift out the tire.

Remove the sill plate. Locate four screws near the four corners of the trunk. Remove these screws and lift out the sill plate. If your vehicle has a cargo net in the trunk, you only need to remove the four screws securing the net. Remove both the net and the sill plate. If your vehicle does not have a cargo net in the trunk, the four screws you need to remove should be located in the corners of your trunk.

After removing the screws, pull the sill plate up to lift it out of the trunk. Set it and the screws aside in a safe spot while you continue working. Pull away the right-side panel. Grab the front of the shell panel on the side of the trunk, and then pull away enough to reveal the interior contents. You should see a silver metal box inside, which is the OnStar unit. Pull the panel forward just enough so that it clears the stud located in the back lip of the trunk. After pulling it forward, carefully pull it toward the middle of the trunk, revealing the compartment beneath it.

Don't remove the panel completely! You can disconnect the OnStar without using any tools to remove additional paneling. Identify the OnStar box. The Onstar control box should be a small metal box attached to the side of the vehicle if in the trunk or inside the plastic paneling in the dash or behind the glove box.

It will usually have an OnStar or LG logo. Don't remove the box. If you do not see the module on the right side, try the left side of the trunk. Unplug all three connectors. Locate the three cable connectors on the bottom of the silver box.

To unplug a connector, grip its base with two fingers and press them inward, and then pull the plug straight out. Repeat until there are no cables connected to the silver box.

Pulling them out should shut down the system and block any additional communication. Coil up the cables.